|
- Handlebar mount
- Integration kit
- Audio plays through headset
- Cell Phones, GPS or Radar
- Accessory Harnesses
- Easy installation
|
|
|
|
|
|
|
|
|
|
Radar Detector Mount, 1" Handlebars |
|
|
|
|
|
|
|
Bluetooth AUX Input Integration Terminal (now shipping) |
|
|
|
Cell Phone, GPS & Radar Integration Kit |
|
|
|
Stereo Music/CB /Weather Radio Audio Sys Solo Operation |
|
|
|
|
|
|
|
Bluetooth Cellphone Adapter |
|
|
|
Zumo 660, 665 Adapter Harness |
|
|
|
|
|
|
|
Valentine One Radar Adapter Harness |
|
|
|
Whistler XTR Radar Adapter Harness |
|
|
|
Bell RX65 Radar Adapter Harness |
|
|
|
Passport 8500 Radar Adapter Harness |
|
SS-1: Mount kit allows most radar detectors to be mounted
to 1' diameter handlebars. Black anodized aluminum with a 316 clear-acrylic mounting plate. Measures 4 L x 3 14 W. Special
sale item.
JM-CFBR-HRUC: This custom made Bluetooth integration terminal
will integrate a Cell-Phone, Smart-Phone, Bluetooth enabled GPS unit and/or specific Radar-Detectors with the driver's (only)
J&M or Harley-Davidson brand corded helmet headset.
While using the normal audio system functions on the Harley
Ultra of stereo music, intercom and/or CB radio, if the cell phone receives an incoming call and the call is accepted by depressing
the handlebar mounted multifunction button, (or onscreen thru a Garmin Zumo) complete connection of the driver's headset to
the cell phone is automatically initiated for totally hands-free operation.
Voice-command-dialing can be activated
by depressing the handlebar mounted multifunction button, which will also initiate complete connection of the driver's headset
to the cell phone, for totally hands-free operation..
If the Bluetooth enabled and linked GPS unit emits any navigation
commands, or the radar detector emits any beeps or braps, regardless of what else might be being heard in the headset, they
will momentarily be heard in the driver’s corded helmet headset.
Once linked the first time, the Bluetooth
enabled cell-phone will automatically connect/disconnect from the system, when the Harley Ultra ignition is turned on or off.
Additional linking/use scenarios are outlined in the installation/operation manual .pdf download listed below.
This is a totally plug-n-play Bluetooth cell-phone integration solution for 1998-2013 Harley, including the new RoadGlide
Ultra model.
Kit includes the plug-in integration module, handlebar-mounted control switch assembly and complete
installation/operation manual.
Note: Specific radar-detector adapter harnesses are available at
extra cost. (please back up to the previous page to purchase these items)
CGR-M1: This component terminal will integrate
the audio signals from a cell phone, GPS and/or radar detector with the driver's (only) helmet headset. If the cell phone normally rings out of its hands-free headset jack,
or emits any other beeps or tones, it will momentarily be heard in the left headset speaker. A flip of the supplied control
switch activates complete connection of the driver's headset to the cell phone for complete hands-free operation. If the radar detector or GPS unit emit any commands, beeps or braps,
regardless of what else might be being heard in the headset, they will momentarily be heard in the right speaker. This kit includes the plug-in integration module, handlebar-mounted control
switch, adapter cables for three-pin and four-pin cell phone headset jacks along with the new adapter cable for the I-phone/Blackberry,
and complete installation and operating instructions. Note: Additional GPS/Radar cable adapters/accessories are available (at extra cost) for a complete plug-and-play
solution.
CGR-BT01:
This new Bluetooth adapter is built specifically to plug into the CGR-M1 (Cell Phone/GPS/Radar) integration module. The audio and microphone signal levels have been tuned by for use with
helmet headsets in the demanding high ambient/wind noise motorcycle riding environment. With this Bluetooth adapter installed the cell phone alert ring tones will be heard in the
helmet headset along with the full feature Bluetooth link capabilities, using the module mounted source volume control rocker
switch and push button feature activator. This kit includes a complete installation and operation manual. CGR-Z550/660: This is a plug-and-play adapter harness
to connect the Garmin ZUMO 550 or 660 to the CGR-M1 Integration module. CGR-VLT1: Bluetooth Dongle Radar Detector Harness Adapter for the Valentine One. This is a direct
plug-and-play adapter harness to connect the Valentine One radar detector to the CGR-M1 unit (Cell Phone/GPS/Radar) or other applicable integration/system modules. (Valentine remote head not needed) Headset volume of the radar beeb/brap
signal is adjusted with the small screw on the harness adapter. CGR-WXTR: Bluetooth Dongle Radar Detector Harness Adapter for Whistler XTR.
This is a direct plug-and-play adapter harness to connect the Whistler XTR radar detector to cgr-m1 unit (Cell Phone/GPS/Radar)
or other applicable integration/system module. Note:
Make sure that your Whistler radar detector has an external speaker jack built into it as parts of it’s design.
CGR-BRX65: Bluetooth Dongle Radar Detector Harness Adapter for Bell RX65. This is a direct plug-and-play
adapter harness to connect the Beltronics RX65 radar detector to the CGR-M1 unit (Cell Phone/GPS/Radar) or other applicable
integration/system modules. CGR-PP85: Bluetooth Dongle Radar Detector Harness Adapter Passport 8500. This is a direct plug-and-play
adapter harness to connect the Passport 8500 radar detector to the CGR-M1 unit (Cell Phone/GPS/Radar) or other applicable
integration/system modules.
JMCB-2003K-SL: This exciting product from features a 40
channel CB radio, an NOAA weather band radio and stereo music amplification from any MP3/I-pod/Sat radio portable-type music
device, completely integrated together into a neat, compact unit for your motorcycle. This new K model has been designed with an expanded 6-circuit aux input plug to accept J&M's new iPod controller
with Bluetooth connection interrupt, to provide the circuits necessary to play music from an iPod, keep the iPod charged while
riding and/or listen to stereo music from a Bluetooth linked device AND actually talk over the cell phone, all thru the same
corded helmet headset (no batteries to charge). This kit includes the radio
head unit, new deluxe solo headset hook-up harness (for one headset only), switchable power supply/noise filter, weather cover,
cable tie straps, hardware and a complete installation and operation manual. (Handlebar mounting bracket, helmet headset,
headset hook-up cord, or the CB antenna, are NOT included as these items are sold separately.) Important Note: The Radio
Head Unit is a 6-pin audio system that requires the pre-amplified microphone signal provided by J&M dual-mode (ECD/ICD/BCD/CD
prefixed) helmet headsets along with the lower section hook-up cord.
|
